DENSOCURE R color
Sealing and finishing color paint
Product Characteristics
Single-component sealing and finishing paint based on synthetic resins and containing water-repellent components. Meets the requirements of EN 1504-2.
- supplied in optimum consistence fit for direct application; no additional dilution is needed
- applied by roller, manual coating or spraying using a suitable air-less equipment
- enhances resistance of surface layers to effects of aggressive media (oils, oil products, inorganic salts, etc.)
- water vapor permeable
- significantly inhibits effects of carbon dioxide upon surface concrete layers
- excellent resistance to atmospheric conditions, permanently water-resistant and resistant to alkaline environment
Use
DENSOCURE R color is a single-component compound based on synthetic resins, and is used for the surface finishing of cement constructions, and for concrete, during repairs of reinforced concrete structures. It is also employed in laying concrete and the fabrication of new concrete elements and surfaces. DENSOCURE R color finds application in the treatment and finishing of floor structures. Meets the requirements of EN 1504-2, attachment ZA, TP ŘSD Sec. 31 and TP SSBK III.
Application of the paint prevents the mixing water of the concrete from evaporating, thus ensuring proper curing and hardening of the concrete floor surface. It suppresses absorption of water and seals the porous structure of the floor surface. All this contributes to improving considerably the chemical durability of the concrete floor surface and facilitates its maintenance. DENSOCURE R color provides long-term protection from water and aggressive components of the atmosphere.
Physical and mechanical parameters
Requirements / results according to EN 1504-2
| Testing method | Requirements | Results | |
| Water vapor permeability | EN ISO 7783-1 | Class I < 5 m | complies |
| Water penetration rate in liquid stage (kg/m2h-0,5) | EN 1062-3 | w < 0.1 | < 0.1 % |
| Adhesive Bond (MPa) | EN 1542 | > 1.5 | > 1.5 |
| Chemical resistance | EN ISO 2812-1 | no visual damage | complies |
| Adhesion bond to wet concrete (MPa) | EN 13578 | pull-off test > 1.5 | complies |
Physical and mechanical parameters
| Color of composition | grey |
| Color of generated film | grey RAL 7032, 7040 |
| Density (g/cm3) | 1.33 ± 0.04 |
| Drying-out (untacky) | Up to 2 hours |
| Recoatability | Up to 4 hours |
| RdCO2 (total coating thickness 100 µm) | > 300 (m) |
Test certificates
Initial tests types according to EN 1504-2 issued by TSÚS Bratislava.
Supervision of the quality system, EMS and OHSAS is carried out by Notified Body No. 1020
Instruction for preparation and application
Base. The base for application of the treatment spray are fresh laid or applied layers of repair materials, concretes and cement mortars and, generally, materials on cement basis. The treated surface shall not be covered by a continuous water film (the surface should be dully dump). Dirt, dust and possible residues of de-striping agents shall be also removed.
Preparation of curing agent. The curing agent is supplied ready for application; no additional dilution is needed.
Neither temperature of the base nor temperature of ambient air shall be below + 5 °C and above + 35 °C.
Applying the coating. DENSOCURE R color should be applied with an airless spray gun. Repeated spraying is recommended to achieve the optimum consumption of 300g/ m2. In absorptive substrate it is recommended to first apply penetration coat using DENSOCURE R in quantity approximately 150 g/ m2.
Immediately following application, the tools and aids should be cleaned with the C 6000 solvent.
Specific consumption
Specific consumption of the DENSOCURE R color coating applied in 2 layers amounts to ca. 300 g/m2 depending on the absorbency and the roughness of the substrate.
More info on the product page
DENSOCURE R color (pdf, 0.4 MB)
